Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks
(152 reviews)
Price: $10.73
In Stock
Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks
Item # UF48-979005
Retail:$23.72
Our Price: $10.73
You Save: 55%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (152)
- Q & A (0)
- Videos (1)
- Photos
Ultra-Fab Products Accessories and Parts - UF48-979005
- Camper Jacks
- Trailer Jack
- Tools
- Ultra-Fab Products
Designed to work with most scissor jacks, this unique socket is used with your power drill to extend and retract your jack up to 10 times faster than with a manual crank. Works with 3/8" drill bits.
Features:
- Socket lets you use a power drill (not included) to speed up extension and retraction of scissor jacks
- Eliminates manual cranking
- Works up to 10 times faster than hand cranking
- Easy operation with a powered drill that uses 3/8" drill bits
- Zinc-plated steel is durable and corrosion resistant
- Non-slip shank
- Hex socket measures 3/4"
- 2-Piece construction
- Lifetime warranty
48-979005 UltraFab Ultra Speed Socket
Video of Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Ultra-Fab Scissor Jack Speed Socket Power Drill Adapter Review
Speaker 1: Today, we're going to be taking a look at the Ultra-Fab speed socket power drill adapter for scissor jacks, part is UF48-979005.Here's what your adapter is going to look like. It's really straight forward setup. This is going to work with any drill that has a minimum opening of 3/8 of an inch, or it can even go into 1/4 inch bit drivers, so it's a pretty versatile setup. Basically, we're going to place it in whatever power tool we want to use, tighten that chuck down, it goes down on it. Then, we can operate our jacks.One thing to keep in mind, if you are backing the screw out, what would traditionally be loosening, that's going to lower the jack. If you go into the tightening, or if you turn it towards the right, that's going to raise the jack.
We'll start with it in reverse. You can see, that's going to be much quicker, much easy, and more simple, than using that hand crank. Especially when it gets hot, the humidity's up, bending over for an extended period of time is not something you want to do. This has been designed to work with the Ultra-Fab scissor jacks, of course, but it'll work with any scissor jack that uses a 3/4 inch socket, here on the end. Now, to raise it back up, would be the opposite process.
Turn our drill so it's tightening, and you can see right up in that stored position.Now, some scissor jacks are going to have a pin that goes through a circle, or there's going to be a flattened tab with a hole in it for J hook to go in. This isn't going to work for those applications, so that's something to keep in mind. That'll complete our look at the Ultra-Fab speed socket power drill adapter for scissor jacks.
Customer Satisfaction Score:
100% were satisfied with this product
0% of customers were not satisfied
- etrailer mistake
Customer Reviews
Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks - UF48-979005
Average Customer Rating: 4.9 out of 5 stars (152 Customer Reviews)
Designed to work with most scissor jacks, this unique socket is used with your power drill to extend and retract your jack up to 10 times faster than with a manual crank. Works with 3/8" drill bits.by: Charles 05/28/2024
Great! Thank You
by: William 05/07/2024
exactly what i expected
by: John 01/30/2024
Works as designed!
by: Aleski11/28/2023
Just good.
by: GaryS_NC08/07/2021
If you have or use scissor jacks under your RV, you'll love this accessory. Just insert it in your cordless drill and in seconds you'll have your jacks extended or retracted. This is a must have! Having a hand crank in addition is also a must to tweak the jacks extension height or if your drill battery dies.
by: Christopher 11/06/2023
Great fit!!!!
by: Steve C05/27/2017
Excellent product - it was just what I needed - thanks for the quick service - this will be a real benefit to me as I have had a stroke and need the assistance in lowering my trailer jacks ... suggest and add-on of axle grease for the jack screws..
Steve C.
5/27/2018
Works great - used several times - so much easier to set up the trailer now
by: Gary08/14/2023
Easy to mount
by: William05/05/2018
Just the right amount of extension to more easily deploy my leveling jacks.
William C.
5/6/2019
Still does the job.
by: Biro07/03/2023
Great 2nd socket to have as a spare.
by: Jeff 06/20/2023
Purchased as a spare. Current one is one-piece and a real time saver.
by: Erik D.12/24/2017
Couldn't do without this tool. Makes operating the trailer stabilizers quick and easy.
Erik D.
12/24/2018
works great!
by: Rich A07/05/2020
This socket saves a ton of time setting up and taking down my stabilizer jacks with the drill that I keep in my trailer. I can recommend it to anyone who would rather spend their time playing when camping instead of working.
by: Bob 11/03/2022
I needed some front end stabilizers for our 19 ft Jayco. These work perfectly... ot too heavy and not too light.
by: double E10/30/2018
I am very happy with the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks. It works just as advertised. I own a cordless impact driver and experimented with chucking up a 3/4" socket to raise and lower the jacks. Don't do it that way! You stand in jeopardy of damaging the jack. Using a convention cordless drill-driver to slowly spin the fitting still requires caution, but is much better. Just remember; once the jack makes contact with the ground, switch over to hand cranking the last few revs. to firm up.
by: Glenn B11/16/2022
etrailer is my go to place when I need something that they sell
by: Vince H.08/27/2015
I bought 2 sets of the 24" ultra-fab scissor jacks and the speed socket. My small 12v cordless drill runs these up and down just fine.
I am looking forward to the reduced movement in my large fifth wheel trailer while these jacks are deployed.
by: PeteD11/25/2016
I use this in my drill to quickly adjust the weight distribution on my Hensley hitch. Saves time and effort a wrench would require.
by: Robert F04/30/2023
Very handy piece of equipment to make RVing easier. Appears well made but a tad on the pricey side for the convenience.
by: Blubuckaroo07/14/2020
This well made adapter is perfect for using my cordless drill to lower & raise our stabilizer jacks.
It's well made and very reasonably priced.
by: andrew C.02/19/2017
This is a life safer for me. Using the drill adapter attached to a portable electric drill makes lowering and raising the four stabilizers on my trailer a breeze. No stress on my back or knees being bent over for what at times seems forever cranking by hand.
by: Wendell07/06/2019
Lifts quickly with impact wrench.
Wendell L.
7/7/2020
Never used it
by: James B03/17/2014
Another great order from etrailer.com. My ordering was simple, the shipping was much faster than expected. The communication from them was solid, every step of process someone sent me an update.
Extremely happy with this supplier.
by: Paul P.07/22/2017
Thank you for promptly packing and shipping my order. It arrived a day earlier than expected!
This product will be a BIG help lowering and raising the RV stabilizers. You offered the best solution at the best price - plus outstanding delivery!
by: P. J.06/11/2015
1. The product is excellent! The product information says it is 10 times faster. I say 20 times faster and takes 0 effort. No more squatting over, cranking away in the heat and humidity. 5 seconds with a drill and Bam!
2. Etrailers price was excellent.
3. I used the more inexpensive of the 3 shipping options, which was $8 and it arrived in only 3 days.
Thank you Etrailer. This is my second purchase from Etariler and I will always check with Etrailer first.
25
152
Show More Reviews
See what our Experts say about this Ultra-Fab Products Accessories and Parts
- Recommended Front Stabilizer Jacks For 2016 Forest River 265RLDSFor your 2016 Forest River 265RLDS, I recommend the Ultra-Fab Ultra Scissor Jacks - 30" Lift - 6,500 lbs - Qty 2 # UF48-979031. I also recommend using the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005 to make adjusting a little easier and faster. If you want a really nice option with dual electric motors, I recommend the Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs # UF39-941707. I've attached a couple videos to assist.
view full answer... - Replacement Stabilizing Jacks For a 2002 Thor Komfort Travel TrailerThe Scissor Stabilizer Jack # TJSC-24 will replace your current stabilizer jacks on your 2002 Thor Komfort 23' travel trailer. This jack is operated by either the 3/4" Socket # UF48-979005 on your drill or with the Manual Crank # TJSC-24-HD.
view full answer... - Availability of Stabilizer Jacks for a Winnebago ViewThe Stabilizer Jack you were looking at, part # TJ01RT can be permanently mounted. Each jack has a 1000 lb capacity. We also offer Scissor Jacks that can be bolted into place. Part # JSC-24 includes 2 jacks with a 5000 lb capacity for each.
view full answer... - Replacing Old Atwood Drop Down Stabilizer JacksReplacement parts are not available for the stabilizer jacks that you have. Your best option would be to replace them. I actually recommend going with something a little more stout that will last longer such as a set of scissor jacks like # UF48-979002. You could then use speed socket # UF48-979005 with an electric drill to make raising and lower the jacks super fast.
view full answer... - Recommended Scissor Jacks For Primetime Avenger Travel Trailer That has 8,400 Lbs Dry WeightWe do carry scissor jacks that can handle the weight you described for your 2014 Primetime Avenger 32BIT Trailer. I recommend the Ultra-Fab Products Trailer Jack, part # UF48-979002. This comes with 2 jacks in the set and each jack has a weight capacity of 6,500 lbs, which gives you a total weight capacity of 13,000 lbs. That is more than enough to handle the 8,400 lbs you said you have. These jacks can be bolted or welded on for installation. To make it easier to raise and lower the...
view full answer... - Can a Drill Adapter be Used on a Standard Type Trailer Jack Like the Bulldog BD190754 The Bulldog Square Jack w/ Footplate part # BD190754 is a nice jack that lifts and lowers the trailer with out the need for a ton on force. This is caused by the nice gear set and the screw they use. With that said I can't recommend that you use a socket adapter like the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks part # UF48-979005 because it is outside of the typical use of the jack defined by the manufacturer. If you were to cut the handle of the jack, thread it, screw...
view full answer... - Adapter to Use a Power Drill to Raise and Lower Scissor Jacks on a TrailerThere are a few different drill adapters for different jacks. The hex head # UF48-979005 sounds like what you describe so we know it won't work. The other type is what is called a T-Slot such as # UF48-979071. It has a shaft length of 2.5 inches, an inner hole diameter of 0.66 inches, and a 0.78 inch slot depth. I included a picture showing these measurements for you. If the T-Slot one will not work then we will not have an adapter that will allow you to use a power drill with the scissor...
view full answer...
- Recommended Trailer Jack Versus Trailer Stabilizer JackThe Ultra-Fab Ultra Scissor Jacks - 24" Lift - 6,500 lbs - Qty 2 # UF48-979002 although they look like the scissor jacks that come with many vehicles for spare tire change are not intended for lifting according to the manufacturer. They are likely strong enough for that use as you stated on your application, but I can't recommend it based on the warranty of the product even though these are rated much higher than the weight you will be lifting. You can absolutely use these to stabilize...
view full answer... - Recommended Stabilizer Support Jack for 40 Foot Trailer When Loading and UnloadingFrom your description, it sounds like you need a stabilizer jack like the Stallion Stabilizer Jacks - 7" Drop Leg Travel - 22-1/4" - Qty 2 # 288-01892-2. These jacks are able to be out of the way when not needed and then add 1000 lb capacity support when needed and up to 650 lbs of lift. This will give you the support and stability you desire for loading and unloading. If you need more support then I recommend the Ultra-Fab Ultra Scissor Jacks - 30" Lift - 6,500 lbs - Qty 2 # UF48-979031....
view full answer... - Replacement A-Frame Tongue Jack That Fits Three Hole 3" Mounting Bolt PatternThe 3" bolt hole spacing is the standard pattern for mounting bolt holes on most trailers. The Lippert Quick Drop Tongue Jack # LC733926 that you are looking at will match that same pattern. Do note that the holes on the jack are oblong to account for slight variations in the size. One thing I do recommend verifying is the diameter of the tube going though the hole. The Lippert jack has a 2-1/4" outer tube diameter. I have seen some older and small trailers only have a 2" diameter hole...
view full answer... - Recommendations for Manual Stabilizer Jack with 22 Inches of LiftThere isn't a manual version of the Ultra_Fab Power Twin stabilizer jack with 22 inches of lift but I do have some options for you. You can use Valterra Folding Manual Stabilizer for Trailers and RVs - 14" to 28" Tall - Aluminum Item # 020106 which uses a ratchet strap to raise/lower the legs. It would have to be placed in an easy to reach location though. Another option is to go with scissor jacks such as # UF48-979031. If you do go with these scissor jacks you can add Ultra-Fab Speed...
view full answer... - Manual Crank For Bulldog Velocity Series Electric Landing Gear Jack BD185402The Bulldog Velocity Series Electric Landing Gear Jack 185402 is a maintenance-free jack so there are no grease points on it. In regards to the manual crank, it simply requires one with a 3/4" hex socket, so you can use one of the following: - Replacement Crank Handle for Lippert Manual Scissor Jack # LC285324 - Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005
view full answer... - How does the Ultra-Fab Speed Socket Power Drill Adapter Operate a Scissor JackMost scissor jacks have a 3/4 inch hex head on the crank shaft. The Ultra-Fab Speed Socket Power Drill Adapter, # UF48-979005, is a universal 3/4 inch socket that fits most standard scissor jacks. If your jack does not have a 3/4 inch hex head for the crank handle, then this socket may not work for your jack. Typically, if scissor jack manufacturers do not use a standard crank handle, then you would want to contact that manufacturer for a replacement crank handle or drill bit options...
view full answer... - Recommended Leveling Jacks For Winnebago ViewThe Stabilizer Jack you came from, part # TJ01RT can be permanently mounted typically under the corners of your camper. Each jack has a 650-lb capacity and are sold individually, and are designed for a smaller RV than your View. The stabilizer jacks I recommend for your Winnebago View are the Stromberg Carlson Leveling Scissor Jacks, part # JSC-24-IND. These jacks mount on the corners of your camper and adjust from 4 inches to 24 inches as needed. Each jack has a capacity of 5,000-lbs....
view full answer... - Weight Capacity And Dimension For Stromberg Carlson Scissor Jack The scissor jacks we offer have weight capacity much higher than the 387 lb you stated you need. All of the jacks we offer are designed for RV use and are intended to be mounted with the top plate. The largest top plate we offer is on the Stromberg Carlson Jack, part # JSC-30-IND. This has a round plate that measures 9 inches diameter. Most jacks have a much higher lift range than the 7.874 inches you stated you need. The # JSC-30-IND has a lift capacity of 5,000 lbs, and does require...
view full answer... - Can Pro Series Trailer Jack - PS1401420303 be Mounted at the Back of a Trailer for SupportYou could put Pro Series Round, Pipe-Mount Swivel Jack # PS1401420303 anywhere that it will fit including at the rear of the trailer to help with support. Usually people use scissor jacks such as # UF48-979031 for this type of application though. The neat thing about these jacks is you can add adapter # UF48-979005 and raise and lower the scissor jacks using an electric drill. That will save you a lot of time and energy.
view full answer... - Recommended Drill Adapter For Stabilizing Jacks On 1992 Coleman 8 Foot Pop-Up CamperThe Drill Adapter for Atwood Direct Drive 5th Wheel Landing Gear is really for the landing gear on a 5th wheel but may work well with other Atwood jacks. However, it's also been discontinued. I believe what you are looking for and recommend is the Ultra-Fab T-Slot Power Drill Adapter for Scissor Jacks # UF48-979071 that is designed to work with most scissor jacks. Another option is the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005. These drill adapters will...
view full answer... - Availability of 12V Motor for Husky Leveling Scissor JackWe do not offer a motor kit for any of the manual scissor jacks we sell. However, we do offer the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks, part # UF48-979005, that allows you to use a cordless power drill to operate the jack at up to ten times the manual cranking speed. For reference I have linked our page for all powered jacks that we offer.
view full answer... - Recommended Socket Adapter To Use With A Drill For Operating A Ultra-Fab Scissor Trailer JackYou sure can use a cordless or corded drill to operate the Ultra-Fab Products Trailer Jack, part # UF48-979002. All you need is the Ultra-Fab Speed Socket Power Drill Adapter, part # UF48-979005. The hex socket is 3/4 inches and will work great in a 3/8 inch drill. Using the socket makes the operation up to 10 times faster. The scissor jack can be used to level and stabilize your trailer, but is not designed for lifting.
view full answer... - Can Ultra-Fab Power Twin II Electric Stabilizers be Installed on a Mercedes Benz Sprinter Cargo VanUltra-Fab Power Twin II Electric Stabilizer # UF39-941705 is designed for trailers but technically it could be installed on your Mercedes Sprinter cargo van. The only issues that you could run into are limited available frame space on the Sprinter and ground clearance. What I recommend is to use a couple of scissor jacks such as # UF48-979002 with the electric drill adapter bit, # UF48-979005 (to raise and lower the jacks fast). I would leave them detached from the vehicle though to eliminate...
view full answer... - Is a Specific Voltage and Size Cordless Drill Needed for Ultra-Fab Speed Socket Power Drill AdapterNo specific voltage of electric drill is required for the Ultra-Fab Speed Socket Power Drill Adapter, # UF48-979005. Any cordless drill will be able to turn the crank up to a certain point but depending on the voltage, the amount of battery life, and the weight of the trailer, any drill can only do so much and then you would need to use the manual handle.The drill will just have to accept 3/8 inch drill bits in order to accept the adapter.
view full answer... - Installation of the Trailer Scissor Stabilization Jack AngleScissor Jacks like the Leveling Scissor Jack - 24" Lift - 5,000 lbs # JSC-24-IND should be mounted at 90 degrees from the trailer frame rail. This allows you to have full crank handle movement of the Crank Handle for Stromberg Carlson Scissor Jacks and Tongue Jacks # JCH-1. The Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005 is and alternative option.
view full answer... - What Is Retracted Height Of Ultra-Fab Products Camper JackThe Ultra-Fab Products Camper Jack, part # UF48-979006 measures 4-3/4 inches tall when fully retracted. The jack has a 24-inch lift and has a large footplate that measures 4-1/2 inches wide and 9-inches long, and this jack has a 6,500-lb support weight capacity. The crank handle is not included with the jack. For the handle you would need part # UF48-879100. To make the job a lot easier you can use the Ultra-Fab Speed Socket Power Drill Adapter, part # UF48-979005. This will work with...
view full answer...
- Scissor Jacks Compatible With JT Strong Arms On a 16 Travel TrailerI recommend using the etrailer Scissor Jacks # TJSCHD-24on your 16' travel trailer. You will need 2 sets of these 24" jacks to get the 4 you need. They will attach to the JT's Strong Arm Jack Stabilizer Kit # LC191025 with the hardware included in the Strong Arm kit. To operate the jacks you can use either the included handle or to speed up the process the Ultra-Fab Speed Socket # UF48-979005 can be used with a cordless drill.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Written by:
Lindsey S
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Jeffrey L
Video by:
Kathleen M
Installed by:
Randy B
Video Edited:
Chris R
Updated by:
Wilson B
Updated by:
Halie H
Updated by:
Eric H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Garys_nc
8/14/2022
This is an absolute must have!. It makes running them and taking them down a breeze.